WinPower Silver
Introduction
Starting Winpower Silver
Main screen
Access levels
Menu description
General configuration
General configuration
General configuration
General configuration
General configuration
General configuration
General configuration
Battery configuration
Battery configuration
Battery configuration
Battery configuration
Battery configuration
Battery configuration
Battery configuration
Battery configuration
System calibration
System calibration
System calibration
System calibration
System calibration
Installation settings
Installation settings
Alarm log
Alarm log
Battery test info
Battery test info
Clear event log
Resynch system
What`s needed?
Ordering information
2.07M
Category: softwaresoftware

WinPower Silver. Communication software for Eltek Power Systems

1. WinPower Silver

Communication software for Eltek Power Systems

2. Introduction

Winpower Silver is a Windows based PC
software for communication with AL 175 &
Flatpack MCU.
MCU and AL 175 is the control/ monitoring
unit used in most small & Medium power
range Eltek rectifier systems today, such as:
Flatpack
MPSU 200 > MPSU 6000
PRSV 700 (Wall mountable cabinets)
PRSB 700 (Floor standing cabinets)

3. Starting Winpower Silver

The screen that appears after starting Winpower Silver on the PC.
A password is needed to get limited access to the monitoring/control unit.

4. Main screen

5. Access levels

Button for changing access level
These access levels are available if the passwords are
known.
Service Access
Change voltage levels and alarm settings.
Installation/setup access
Change system setup.

6. Menu description

Password
Installation
Calibration
Battery configuration
General configuration
About
Resynch system
Clear event log
Battery test info
Alarm log

7. General configuration

Set levels:
For:
Battery voltage,
LVD’s
Alarm and security
levels

8. General configuration

Alarm setup/
display:
Configuring
alarms to trig
relays or modem.

9. General configuration

Set time:

10. General configuration

Site info:
Site specific
data for
identification
and information

11. General configuration

Modem callback:
Predefined phone
numbers for modem
callback.
ID text string.
Settings for automatic
modem callback

12. General configuration

General
configuration:
Setting of slope and
levels for
temperature
compensated
charging.

13. General configuration

Relay Test:
Allows on site test of:
Alarm relay operation
External alarm wiring
Operation of the LVD

14. Battery configuration

Battery configuration:

15. Battery configuration

Battery test setup:
Setup of test limits
Setup for automatic
battery test
Starting
a manual test

16. Battery configuration

Auto boost:
Set threshold based
on discharged capacity
Set max. boost time
Set to boost charge
to a percentage of the
discharge

17. Battery configuration

Manual boost:
Start a boost charge.
Set boost duration

18. Battery configuration

Battery type:
Choose the type of
batteries installed
Set no. of
battery strings
Enter total resistance
in the battery cables,
to compensate for the
voltage drop.

19. Battery configuration

Charge current
limitation:
Activate /
deactivate charge
current limitation
Set maximum
charge current for
the batteries (total
for all strings)

20. Battery configuration

Output
control: configuration
Battery
Define how the output
voltage should be regulated
Temperature
compensation:
Voltage according to temp.
(temp.probe installed)
Output voltage control:
Alarm module adjusts the
voltage to the pre-set level
Default rectifier voltage:
Use the rectifiers internal set
voltage

21. Battery configuration

Batt. Setup User def.:
Naming non defined
batteries
Enter discharge data
for non defined batteries
Set the end voltage for
a battery test of these
batteries
Set the data for temp.
compensated charging of
these batteries

22. System calibration

System calibration

23. System calibration

Temperature:
Recalibration of the
temperature reading.
A temp. simulator is
required (supplied by
Eltek Energy)

24. System calibration

Rectifier current:
Recalibration of the
rectifier current
reading.

25. System calibration

Output voltage:
Recalibration of the
output voltage reading.

26. System calibration

Battery current:
Recalibration of
the battery current
reading.

27. Installation settings

Installation settings

28. Installation settings

System
config:
Installation
settings
Set system type
Set nominal voltage
Set rectifier type
Set I/O
configuration (custom)
Type of contactor
used
Enable symmetry
alarm
Enable Auto Boost

29. Alarm log

Alarm log

30. Alarm log

Alarm log:
List of the last 255
events that have
occured in the
system.
Export log to PC
Erase log

31. Battery test info

Battery test information

32. Battery test info

Battery test results:
View the results of the
two last battery tests

33. Clear event log

Clears the event log in the bottom part of the window.

34. Resynch system

Resynch system
Restarts alarm module and
communication between the PC and the system

35. What`s needed?

PC requirements:
WinPower Silver runs on Windows 98, Windows ME and
Windows 2000.
Eltek RS 232 serial communication cable.
System requirements:
MCU or AL175 monitoring / control unit
Most new systems are configured for WinPower
Systems using VT-100 needs a SW upgrade in order to
communicate with the WinPower PC-software (Pcomm
protocol, contact Eltek Energy for details)

36. Ordering information

WinPower silver contains the following part
numbers:
402022.003
240278.xxx
35xxxx.xxx
100359
PROM for Alarm module (SW)
PC software and User Guide on CD-ROM
User Guide (hardcopy)
Communication cable 1,5m
English     Русский Rules