11.27M
Category: softwaresoftware

wifi902 Diagnostic Software Installation and Tutorial

1.

wifi902英文版
安装以及使用教程
wifi902 Diagnostic Software
Installation and Tutorial

2.

插上加密狗并连上诊断仪
P l u g i n s of t d o g a n d c o n n e c t t h e d i a g n o s t i c
equipment

3.

双 击 F T D I C D M D r i ve r s 安 装 9 0 2 驱 动
d o u b l e c l i c k F T D I C D M D r i ve r s

4.

等待一会并完成
Click done after waiting

5.

双击HED_ST_EN.20210615 setup 安装软件
double click HED_ST_EN.2021061 setup

6.

该程序安装完成
This progress accomplished

7.

桌面上出现该图标 并双击
Now an icon present to your desk
and double click it

8.

如果桌面没有出现该图标 则进入开始菜单进行寻找
Enter star t menu if the icon don′t show on your desk

9.

点击update 等候5分钟 完成。
Choose update waiting5 minute
completed

10.

点击MSVBcr tAio,运行库合集2019.07
Click MSVBcr tAio

11.

选择不重启电脑 因为还有工具需要安装
C h o o s e “ N o t t o r e s t a r t ” a n d c l i c k f i n i s h ( We h a v e n o
install instrument yet)

12.

点击HASP 阿拉丁驱动
Click HASP

13.

点 击 Re g i s t e r YC D C U
C l i c k Re g i s t e r

14.

插上加密狗并连上诊断仪
P l u g i n s of t d o g a n d c o n n e c t t h e d i a g n o s t i c
equipment

15.

找到对应的OBD接口Find the right connection group in OBD
socket
①K-Line:7
GND:4
VCC : 1 6 F o r B o s c h C R Sy s t e m
②CAN-H0:6
C A N - L 0 : 1 4 F o r YC D C U
③CAN-H1:3
CAN-L1: 11
OBD socket

16.

先尝试进入博世共轨系统 并找到对应线组
Tr y t o e n t e r B o s c h C R Sy s t e m a n d
find the right wire group

17.

找到接线组①的位置并插在OBD口里
Find the connection group ① and
p l u g t h e w i r e s i n O B D s o c ke t

18.

打开海能诊断软件
O p e n t h e s of t w a r e

19.

接好控制器和诊断仪的线后进入博世共轨系统
E n t e r t h e B o s c h C R Sy s t e m a f t e r t h e c o n n e c t i o n
between ECU/RCU/DCU and diagnostic equipment

20.

其它系统介绍
I n t r o d u t i o n of o t h e r s y s t e m

21.

诊断仪会显示两个绿灯
The diagnostic equipment will show two green
lights when connection completed

22.

成功进入时会显示软件版本号
I t s h o w s t h e s of t w a r e ve r s i o n w h e n y o u a r e
login successful

23.

在“帮助”里可以找到各种信息
Yo u c a n f i n d a l l k i n d s of i n f o i n “ H e l p ”

24.

读取故障功能
Re a d Fa u l t F u n c t i o n

25.

清除故障功能
C l e a n Fa u l t F u n c t i o n

26.

监测数据和断缸测试功能
M o n i t o r a n d D i a g Te s t F u n c t i o n

27.

数据监测里的功能 按钮依次为制作模板、载入模板、开
始记录、返回
As shown in the figure Monitor function

28.

停止检测和保存检测数据功能
As shown in the figure Monitor function

29.

刷写新程序Prog Hex:
1、点击Prog Hex按钮 上传新程序
2、等待新程序刷写完成 然后关闭钥匙3分钟
3、重新打开钥匙开关 然后重新打开诊断软件。
4、启动发动机 检查故障灯是否亮 是否可以达到最高转速
Flash the new program Prog
1. Click the Prog Hex button to upload a new program
2. Wait for the new program to be flashed, and then turn off the key for 3
minutes
3. Turn the key switch back on, and then re -open the diagnostic software.
4. Start the engine, check whether the fault light is on, and whether it can
reach the maximum speed
Flash the new program
Prog

30.

TITLE 1
谢谢 THANKS
THANKS
版权归广西玉柴机器股份有限公司所有 Copyrights are held by Guangxi Yuchai Machinery Co., Ltd.
English     Русский Rules