Lecture 6. Sloping Rafter and Braced-Beam Systems
Sloping Rafter Systems
Stability of the system
Structural Arrangements and Connections of Sloping Rafters
Materials and minimum dimensions
4. Structural behaviour of rafters
Structural behaviour of rafters
Design of individual elements
Combined Structural Systems
Combined Structural Systems
Table 5.1. Forces in the Elements of Combined Systems
Effective member lengths
Braced-Beam Systems
Structural Arrangements and Connections of Braced-Beam Systems
Connections in braced-beam systems
Structural analysis
Table 5.2. Forces in Queen-Post Systems
Table 5.3. Forces in Braced-Beam Systems
Key numerical values to remember
Conclusion
2.87M

Lecture 6 пдк

1. Lecture 6. Sloping Rafter and Braced-Beam Systems

Prepared by: Niyetbay S.
Lecture 6.
Sloping Rafter and Braced-Beam
Systems

2. Sloping Rafter Systems

Important dimensions
• Maximum distance between
the principal supports:
approximately 7 m.
• Recommended spacing
between posts: not more than
6 m.
• Normal spacing between rafter
legs: 1.0–1.5 m.
• The exact spacing depends on
the load-bearing capacity of
the roof sheathing and roof
covering.
1. General description
A sloping rafter system is used to support the roof covering and roof
sheathing in buildings with an attic. This system is suitable when the
distance between load-bearing walls or other supports does not exceed
approximately 7 m.
The main load-bearing elements are inclined rafter legs. At the outer walls,
the rafters rest on wall plates called mauerlats. At internal walls or
columns, they are supported by longitudinal upper purlins.
When the rafter span is large, additional inclined braces are installed. The
braces reduce the effective span of the rafters and transfer forces to lower
longitudinal members called sills. Vertical posts transfer forces from the
upper purlins to these sills.

3. Stability of the system

The roof structure must be
stable in both the
longitudinal and transverse
directions.
Longitudinal stability is
provided by:
longitudinal braces;
vertical bracing;
connections between posts
and purlins;
roof sheathing and other
roof elements.
Transverse stability is
provided by:
collars or horizontal ties;
diagonal bracing;
crossed vertical bracing in
three-span buildings;
secure connections
between opposite rafters.
If there are no longitudinal
braces, additional bracing
must be installed in the
longitudinal direction.
The rafter system is not only
a set of inclined beams. It is
a complete spatial system
in which rafters, purlins,
posts, braces, ties and
connections work together.

4. Structural Arrangements and Connections of Sloping Rafters


Description of the figure
The figure presents different
arrangements of sloping rafter
systems:
Scheme a: a two-span building with
a total width of less than 10,000
mm;
Scheme b: a two-span building with
a width of up to 14,000 mm;
Scheme c: a three-span building
with a width of up to 18,000 mm and
a central span of up to 4,000 mm;
Scheme d: a hip-roof arrangement;
Sections I–I, II–II and III–III:
longitudinal and transverse bracing
arrangements;
Details A–E: typical structural
connections at the wall plate, ridge,
purlin, sill and brace.
The diagram also shows how roof
loads are divided into horizontal and
slope-parallel components.
Main components shown in the figure
1. Timber cleat with a section of 50 ×
100 mm
2. Rafter leg
3. Nail with a diameter of
approximately 5 mm and a length
of 150 mm
4. Wire tie
5. Wall plate or mauerlat
6. Notched connection
7. Purlin
8. Steel tie rod with a diameter of 16–
20 mm
9. Vertical post
10. Horizontal tie
11. Cross bracing made of steel strips
12. Brace
13. Sill
14. Timber bearing pad with a section
of 50 × 200 mm
15. Wall plate
16. Diagonal rafter
17. Collar tie
18. Steel bracket or staple

5. Materials and minimum dimensions

The elements of a traditional
sloping rafter system may be
made from round timber with
natural taper. This can reduce
timber consumption because the
shape of the log is used efficiently.
Sawn timber may also be used,
especially when the components
are prefabricated in a factory and
delivered to the construction site
as ready-made elements.
Minimum recommended
dimensions
Rafter legs, posts and braces
made from round timber:
diameter not less than 120 mm.
Mauerlats and longitudinal
purlins: diameter not less than
160 mm.
Timber bracing made from boards:
section not less than 50 × 100
mm.
Short wall-plate sections: length
approximately 500–700 mm.
Timber pads under posts:
diameter 160–180 mm and length
500–700 mm.
Coniferous and soft deciduous
timber may be used. The source
specifically mentions spruce,
poplar and second-grade aspen.
When opposite rafters rest on the
same purlin, they should be
placed opposite each other and
connected at the ridge and to the
purlin. This arrangement helps
prevent lateral bending or twisting
of the purlin.
Continuous timber sill: diameter
approximately 160 mm.

6. 4. Structural behaviour of rafters

• Rafter legs are normally calculated as simply supported inclined beams resting on two supports.
• The main design loads are:
• permanent load from the self-weight of the roof;
• snow load;
• wind load.
• The vertical distributed load \(q\) is collected from a tributary width equal to the spacing between adjacent rafters.
• The load may be divided into two components:
•
English     Русский Rules